Brackets 1 11

Forward + Medium Punch (Rock Crusher) 20 42 300, 300 Overhead, High -- -- -- +3 -3 3 20 Forward + Medium Kick (Double Knee Bombs) 9, 8 38 300, 300 High, High -- As of December 2024 patch: reduced hurtbox on frame 9. Anti-air hit is now a blowback knockdown. -- +6 -2 3, 2 18 Back + Medium Kick (Wild Edge) 9 26 600 High Special, Super -- -- +8 +2 6 12 Forward + Heavy Punch (Wild Nail) 18 49 1100 High -- As of December 2024 patch: knockdown from +18 to +20 for ground hits, from +18 to +23 for anti-air hits. -- Knockdown +20 (Knockdown +23 as an anti-air) -15 4 31 Down-Forward + Heavy Punch (Amazon River Run) 14 45 1000 Low -- -- -- Knockdown +29...+38 -18...-9 10 22 Jump Light Punch 4 -- 300 Overhead -- -- -- +4... 0... 5 3 Landing Jump Medium Punch 7 -- 700 Overhead Special Limited Juggle State on hit. -- +5... +1... 7 3 Landing Jump Heavy Punch 9 -- 800 Overhead -- Knockdown on aerial hit. -- +6... +2... 4 3 Landing Jump Light Kick 5 -- 300 Overhead -- -- -- +5... +1... 6 3 Landing Jump Medium Kick 7 -- 500 Overhead -- Crosses up. -- +8... +4... 6 3 Landing Jump Heavy Kick 11 -- 800 Overhead -- -- -- +9... +5... 6 3 Landing Neutral Jump Heavy Punch 7 -- 800 Overhead -- Limited Juggle State on aerial hit. -- +10... +6... 3 3 Landing --> Electric Thunder 10 Down, Down-Back, Back + P 38 800 [900] High Hold button to continue electric hits (whiff only). Lightning Beast buff damage in brackets. -- Knockdown +39 -3 2, 2, 2 15 --> Electric Thunder (Overdrive) 10 Down, Down-Back, Back + PP 38 400, 600 [500, 600] High Hold button to continue electric hits (whiff only). -- Knockdown +40 +4 2, 2, 2 17 --> Rolling Attack (Light Punch) 10 Back Charge, Forward + Light Punch 31 (58...) 1000 [1100] High Lightning Beast data in brackets. -- Knockdown +13 -23 [-21] 11 [12] 11 (42) [10 (39)] --> Rolling Attack (Medium Punch) 12 Back Charge, Forward + Medium Punch 41 (58...) 1200 [1300] High Lightning Beast data in brackets. -- Knockdown +14 -23 [-21] 19 11 (42) [11 (39)] --> Rolling Attack (Heavy Punch) 12 Back Charge, Forward + Heavy Punch 66 (58...) 1300 [1400] High Lightning Beast data in brackets. -- Knockdown +30 -15 [-21] 20 [22] 25 (33) [25 (39)] --> Rolling Attack (Overdrive) 18 Back Charge, Forward + PP 45 (**...) 800 [900] High Lightning Beast data in brackets. Limited Juggle State on hit. -- Knockdown +57 -7 22

Using a hammer. Repeat on opposite side of structure. Move up to lower ANGLE BRACKET “A” remove scrap boards and place RIDGE BOARD into slots in lower “A” brackets. Repeat on opposite side of structure. Remove scrap boards from top ANGLE BRACKET “A” and place RIDGE BOARD into slots in top “A” angle brackets. Make sure all arch assemblies are in correct positioning and adjust if needed. Secure all RIDGE BOARDS using screws through bottom holes in ANGLE BRACKETS. (For 10’ x 22’ structures, see #4 of Helpful Hints)11. Install DOOR JAMBS as shown in FRONT VIEW drawings in accordance with your building size. Nail top of DOOR JAMBS to COLLAR TIE of end arch assembly. Screw STUD BRACKETS to bottom of each DOOR JAMB. Attaching to outside of top BASE PLATE.12. Install two VERTICAL STUDS in back wall. (Same layout as Step 11) Nail top of VERTICAL STUDS to COLLAR TIE of end arch assembly. Screw STUD BRACKETS to bottom of each VERTICAL STUD. Attaching to outside of top BASE PLATE.13. Your frame is now complete and ready to sheathe with materials of your choice. (See Helpful Hints)HELPFUL HINTS (ALL SIZES)1. Install wall sheathing horizontally on sides of 7’X8’ building. Install wall sheathing vertically on ends of 7’X8’ building. Install all wall sheathing vertically on larger size buildings. Install roof sheathing horizontally on all building sizes. Save the pieces of sheathing that you cut off and use them elsewhere (such as the other side of the roof). Use completed arch as pattern to trace cut lines on sheathing for ends of building.2. Roofing material may be metal, corrugated fiberglass, rolled roofing or shingles.3. Doors can be cut from plywood sheathing. Outline each half with 1X4 boards to make them rigid. Screw hinges to door jambs. On larger buildings, full

Home » Catalog » Clock Repair & Replacement Parts » Cuckoo Clock Parts » Cuckoo Clock Tops & Mounting Brackets Timesavers - Cuckoo Clock Tops & Mounting Brackets Stained & unfinished bird & hunting tops and metal brackets Browse Cuckoo Clock Tops & Mounting Brackets Products Items 1-19 of 19 Description: Unfinished cuckoo clock frame. Item #: 33264 Condition: New Description: Hand carved wood cuckoo top with birds and leaves. Measures 7-3/8" from end to end. Made in Germany. Stained blonde with walnut brown highlights. Item #: 33133 Condition: New Description: Hand carved wood cuckoo top with birds and leaves. Measures 9-1/2" from end to end. Made in Germany. Stained walnut brown. Item #: 29254 Condition: New Description: Hand carved wood cuckoo top with birds and leaves. Measures 9-1/2" from end to end. Made in Germany. Stained blonde & brown. Item #: 29255 Condition: New Description: Hand carved brown wood tops with wood deer head and brown plastic antlers. Size is measured end to end. 7". Item #: 29409 Condition: New Description: Stamped steel mounting bracket is used to mount cuckoo tops. 3/8" wide x 5/8" long. Item #: 15816 Condition: New Description: Cuckoo clock horn and mouthpiece set is made in Germany. The horn diameter is 42mm (1-5/8"), and the set is stained walnut brown. Item #: 17422 Condition: New Description: Used to mount cuckoo tops on clock roofs. Item #: 22917 Condition: New Description: Hand carved wood cuckoo top with birds and leaves. Measures 11-1/2" from end to end. Made in Germany. Stained blonde with walnut brown highlights. Item #: 10796 Condition: New Description: Hand carved wood cuckoo top with birds and leaves. Measures 8-1/4" from end to end. Made in Germany. Stained blonde with walnut brown highlights. Item #: 10794 Condition: New Description: Hand carved wood cuckoo